Вега 2.2 не грузится

LoRa, LoRaWAN, Вега Smart
Ответить
sudo
Мимо проходил
Сообщения: 16
Зарегистрирован: Чт, 29 июл 2021 15:34

Вега 2.2 не грузится

Сообщение sudo » Пт, 27 янв 2023 14:31

Вега 2.2 rev 2 (синяя плата) от 02.2022

Падает в Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Лог загрузки https://pastebin.com/J9Sdu5x6

Аватара пользователя
a.leonov

Re: Вега 2.2 не грузится

Сообщение a.leonov » Пт, 27 янв 2023 15:28

sudo писал(а):
Пт, 27 янв 2023 14:31
Вега 2.2 rev 2 (синяя плата) от 02.2022

Падает в Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Лог загрузки https://pastebin.com/J9Sdu5x6
Добрый день!

Критическая ошибка.
Вам необходимо отправить БС в ремонт. Для получения информации, Вам нужно обратиться по e-mail: remont@vega-absolute.ru

sudo
Мимо проходил
Сообщения: 16
Зарегистрирован: Чт, 29 июл 2021 15:34

Re: Вега 2.2 не грузится

Сообщение sudo » Пт, 27 янв 2023 16:43

Через час ожидания на ошибке - завелась. Ошибки больше нет - грузится штатно. Возникает подозрение на разрушение bga пайки, т.к. перед "завелась", за пару минут до, воткнул usb-lan карту в разъем usb. Возможно, незначительный изгиб платы привел к "уседанию" поврежденного шара. Без проявления деффекта - в СЦ не примут...

И еще вопрос - есть ли возможность "слить" дамп с NAND.rootfs с одной БС и залить его в другую БС? Есть ли инструкция как это сделать через u-boot? К примеру - есть БС(другая), которая залипла на загрузке. Она проверяет некий параметр при загрузке системы, не обнаруживает параметр, перезагружает систему. Так вот эта проверка происходит до поднятия сети, т.о. по ssh не получится остановит выполнение скрипта. CTRL+C +X +Z +D не дают результата и через com-терминал. Как отредактировать память rootfs или вернуть ее исходное состояние?

Bombandil
Мимо проходил
Сообщения: 20
Зарегистрирован: Чт, 05 май 2022 18:59

Re: Вега 2.2 не грузится

Сообщение Bombandil » Чт, 09 фев 2023 13:48

то же самое.
синяя плата и следующие данные

Код: Выделить всё

U-Boot SPL 2013.10-00189-g78d8ebd-dirty (Jul 27 2017 - 18:56:52)
CORE_AM335x_v3 module configuration
The Expected Linux image was not found. Please check your NAND configuration.
Trying to start u-boot now...
nand: bit-flip corrected @data=438
nand: bit-flip corrected @data=438


U-Boot 2013.10-00189-g78d8ebd-dirty (Jul 27 2017 - 18:56:52)

I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net:   Could not get PHY for cpsw: addr 0

Devname: cpsw

cpsw, usb_ether
Hit any key to stop autoboot:  0
Card did not respond to voltage select!
mmc0(part 0) is current device
Scanning mmc 0...
Card did not respond to voltage select!
** Bad device mmc 0 **
Card did not respond to voltage select!
mmc0(part 0) is current device
Card did not respond to voltage select!
Card did not respond to voltage select!
mmc1(part 0) is current device
Card did not respond to voltage select!
Booting from nand ...

NAND read: device 0 offset 0x80000, size 0x40000
 262144 bytes read: OK

NAND read: device 0 offset 0x200000, size 0x800000
nand: bit-flip corrected @data=448
nand: bit-flip corrected @data=182
nand: bit-flip corrected @oob=0
nand: bit-flip corrected @data=335
nand: bit-flip corrected @data=342
nand: bit-flip corrected @data=139
nand: bit-flip corrected @data=321
nand: bit-flip corrected @data=420
nand: bit-flip corrected @data=36
nand: bit-flip corrected @data=357
nand: bit-flip corrected @data=171
nand: bit-flip corrected @data=376
nand: bit-flip corrected @data=221
nand: bit-flip corrected @data=324
nand: bit-flip corrected @data=422
nand: bit-flip corrected @data=487
nand: bit-flip corrected @oob=7
nand: bit-flip corrected @data=140
nand: bit-flip corrected @data=122
nand: bit-flip corrected @data=169
 8388608 bytes read: OK
Kernel image @ 0x80200000 [ 0x000000 - 0x3d61d8 ]
## Flattened Device Tree blob at 80f80000
   Booting using the fdt blob at 0x80f80000
   Loading Device Tree to 8f320000, end 8f32bc48 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.12.10-ti2013.12.01 (root@alexander-VirtualBox) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Sat May 18 17:44:30 +07 2019
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: VEGA-BS-AM335x
[    0.000000] cma: CMA: reserved 24 MiB at 8d800000
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] AM335X ES2.1 (neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64256
[    0.000000] Kernel command line: console=ttyO0,115200n8 root=ubi0:rootfs rw ubi.mtd=NAND.file-system,2048 rootfstype=ubifs rootwait=1
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 223668K/259072K available (5415K kernel code, 553K rwdata, 1836K rodata, 329K init, 210K bss, 35404K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc071d08c   (7253 kB)
[    0.000000]       .init : 0xc071e000 - 0xc0770554   ( 330 kB)
[    0.000000]       .data : 0xc0772000 - 0xc07fc558   ( 554 kB)
[    0.000000]        .bss : 0xc07fc558 - 0xc0830e40   ( 211 kB)
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: timer1 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000345] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[    0.049698] pid_max: default: 32768 minimum: 301
[    0.049808] Security Framework initialized
[    0.049865] Mount-cache hash table entries: 512
[    0.059243] CPU: Testing write buffer coherency: ok
[    0.059659] Setting up static identity map for 0xc054ff28 - 0xc054ff98
[    0.060672] devtmpfs: initialized
[    0.062779] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    0.126492] omap_hwmod: debugss: _wait_target_disable failed
[    0.127242] pinctrl core: initialized pinctrl subsystem
[    0.128175] regulator-dummy: no parameters
[    0.130829] NET: Registered protocol family 16
[    0.133355] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.136104] cpuidle: using governor ladder
[    0.136123] cpuidle: using governor menu
[    0.146562] platform mpu.1: FIXME: clock-name 'fck' DOES NOT exist in dt!
[    0.147808] platform 49000000.edma: FIXME: clock-name 'fck' DOES NOT exist in dt!
[    0.148383] omap_gpio 44e07000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio0_pins_default, deferring probe
[    0.148412] platform 44e07000.gpio: Driver omap_gpio requests probe deferral
[    0.148756] omap_gpio 4804c000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio1_pins_default, deferring probe
[    0.148779] platform 4804c000.gpio: Driver omap_gpio requests probe deferral
[    0.149103] omap_gpio 481ac000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio2_pins_default, deferring probe
[    0.149126] platform 481ac000.gpio: Driver omap_gpio requests probe deferral
[    0.149457] omap_gpio 481ae000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio3_pins_default, deferring probe
[    0.149480] platform 481ae000.gpio: Driver omap_gpio requests probe deferral
[    0.155906] omap-gpmc 50000000.gpmc: could not find pctldev for node /pinmux@44e10800/nandflash_pins_s0, deferring probe
[    0.155939] platform 50000000.gpmc: Driver omap-gpmc requests probe deferral
[    0.156376] platform 56000000.sgx: FIXME: clock-name 'fck' DOES NOT exist in dt!
[    0.158253] DSS not supported on this SoC
[    0.158269] No ATAGs?
[    0.158282] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.187109] bio: create slab <bio-0> at 0
[    0.204056] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.205013] vmmcsd_fixed: 3300 mV
[    0.209432] SCSI subsystem initialized
[    0.211063] usbcore: registered new interface driver usbfs
[    0.211277] usbcore: registered new interface driver hub
[    0.211515] usbcore: registered new device driver usb
[    0.212566] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe
[    0.212598] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral
[    0.212850] media: Linux media interface: v0.10
[    0.213057] Linux video capture interface: v2.00
[    0.213363] pps_core: LinuxPPS API ver. 1 registered
[    0.213375] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.213527] PTP clock support registered
[    0.216460] Switched to clocksource timer1
[    0.238465] NET: Registered protocol family 2
[    0.239176] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.239238] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.239275] TCP: Hash tables configured (established 2048 bind 2048)
[    0.239352] TCP: reno registered
[    0.239368] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.239391] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.239599] NET: Registered protocol family 1
[    0.240038] RPC: Registered named UNIX socket transport module.
[    0.240051] RPC: Registered udp transport module.
[    0.240060] RPC: Registered tcp transport module.
[    0.240068] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.241110] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.241793] PM: Loading am335x-pm-firmware.bin
[    0.422265] VFS: Disk quotas dquot_6.5.2
[    0.422357] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.423007] NFS: Registering the id_resolver key type
[    0.423096] Key type id_resolver registered
[    0.423107] Key type id_legacy registered
[    0.423162] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.423381] msgmni has been set to 484
[    0.425236] NET: Registered protocol family 38
[    0.425282] io scheduler noop registered
[    0.425292] io scheduler deadline registered
[    0.425316] io scheduler cfq registered (default)
[    0.427614] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.431172] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.434165] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    1.120536] console [ttyO0] enabled
[    1.125107] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    1.136398] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20
[    1.155062] brd: module loaded
[    1.164429] loop: module loaded
[    1.172496] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.181685] edma-dma-engine edma-dma-engine.0: allocated channel for 0:43
[    1.188934] edma-dma-engine edma-dma-engine.0: allocated channel for 0:42
[    1.200318] PPP generic driver version 2.4.2
[    1.205323] PPP BSD Compression module registered
[    1.210324] PPP Deflate Compression module registered
[    1.215718] PPP MPPE Compression module registered
[    1.220793] NET: Registered protocol family 24
[    1.225757] usbcore: registered new interface driver zd1201
[    1.231906] usbcore: registered new interface driver asix
[    1.237848] usbcore: registered new interface driver ax88179_178a
[    1.244489] usbcore: registered new interface driver cdc_ether
[    1.250811] usbcore: registered new interface driver r815x
[    1.256819] usbcore: registered new interface driver smsc95xx
[    1.263090] usbcore: registered new interface driver net1080
[    1.269221] usbcore: registered new interface driver cdc_subset
[    1.275671] usbcore: registered new interface driver zaurus
[    1.281799] usbcore: registered new interface driver cdc_ncm
[    1.288334] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.295213] ehci-pci: EHCI PCI platform driver
[    1.300139] ehci-omap: OMAP-EHCI Host Controller driver
[    1.306699] usbcore: registered new interface driver cdc_acm
[    1.312659] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.321316] usbcore: registered new interface driver cdc_wdm
[    1.327533] usbcore: registered new interface driver usb-storage
[    1.334318] usbcore: registered new interface driver usbserial
[    1.340686] usbcore: registered new interface driver option
[    1.346763] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.355283] mousedev: PS/2 mouse device common for all mice
[    1.362926] input: ti-tsc as /devices/ocp.2/44e0d000.tscadc/TI-am335x-tsc/input/input0
[    1.373629] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    1.381196] 44e3e000.rtc: already running
[    1.386249] i2c /dev entries driver
[    1.390590] Driver for 1-wire Dallas network protocol.
[    1.398529] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.407639] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    1.414820] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    1.457314] platform leds.3: Driver leds-gpio requests probe deferral
[    1.467501] ledtrig-cpu: registered to indicate activity on CPUs
[    1.474258] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    1.481522] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    1.489176] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    1.495280] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    1.502475] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    1.512278] usbcore: registered new interface driver usbhid
[    1.518192] usbhid: USB HID core driver
[    1.524736] oprofile: no performance counters
[    1.529850] oprofile: using timer interrupt.
[    1.534680] TCP: cubic registered
[    1.538209] Initializing XFRM netlink socket
[    1.542790] NET: Registered protocol family 17
[    1.547538] NET: Registered protocol family 15
[    1.552276] 8021q: 802.1Q VLAN Support v1.8
[    1.556727] lib80211: common routines for IEEE802.11 drivers
[    1.562796] Key type dns_resolver registered
[    1.568001] cpu cpu0: cpu0 regulator not ready, retry
[    1.573355] platform cpufreq-cpu0.0: Driver cpufreq-cpu0 requests probe deferral
[    1.581839] ThumbEE CPU extension supported.
[    1.589247] OMAP GPIO hardware version 0.1
[    1.596906] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    1.602336] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[    1.609903] ONFI param page 0 valid
[    1.613592] ONFI flash detected
[    1.616960] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (Macronix MX30LF2G18AC), 256MiB, page size: 2048, OOB size: 64
[    1.628806] omap2-nand: detected x8 NAND flash
[    1.633491] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    1.639134] omap2-nand: using custom ecc layout
[    1.644065] 10 ofpart partitions found on MTD device omap2-nand.0
[    1.650520] Creating 10 MTD partitions on "omap2-nand.0":
[    1.656230] 0x000000000000-0x000000020000 : "NAND.SPL"
[    1.663448] 0x000000020000-0x000000040000 : "NAND.SPL.backup1"
[    1.671267] 0x000000040000-0x000000060000 : "NAND.SPL.backup2"
[    1.679069] 0x000000060000-0x000000080000 : "NAND.SPL.backup3"
[    1.686879] 0x000000080000-0x0000000c0000 : "NAND.u-boot-spl-os"
[    1.694958] 0x0000000c0000-0x0000001c0000 : "NAND.u-boot"
[    1.703057] 0x0000001c0000-0x0000001e0000 : "NAND.u-boot-env"
[    1.710804] 0x0000001e0000-0x000000200000 : "NAND.u-boot-env.backup1"
[    1.719290] 0x000000200000-0x000000a00000 : "NAND.kernel"
[    1.733127] 0x000000a00000-0x000010000000 : "NAND.file-system"
[    1.948272] DCDC1: at 1500 mV
[    1.953631] vdd_core: 1100 mV
[    1.957875] vdd_mpu: 925 <--> 1350 mV at 1275 mV
[    1.963831] LDO1: at 1800 mV
[    1.967942] LDO2: at 3300 mV
[    1.972583] LDO3: 1800 mV
[    1.976415] LDO4: at 3300 mV
[    1.980331] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[    1.985975] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[    1.994900] cpufreq_cpu0: Bootloader freq 600000000Hz no match to table, Using 300000000Hz
[    2.006871] UBI: attaching mtd9 to ubi0
[    2.319010] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read only 64 bytes, retry
[    2.331490] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read only 64 bytes, retry
[    2.343956] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read only 64 bytes, retry
[    2.356415] UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read 64 bytes
[    2.367133] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.10-ti2013.12.01 #1
[    2.374563] Backtrace:
[    2.377263] [<c0017880>] (dump_backtrace+0x0/0x10c) from [<c0017a1c>] (show_stack+0x18/0x1c)
[    2.386303]  r6:cd29e000 r5:00000040 r4:ffffffb6 r3:00000000
[    2.392456] [<c0017a04>] (show_stack+0x0/0x1c) from [<c0548750>] (dump_stack+0x20/0x28)
[    2.401047] [<c0548730>] (dump_stack+0x0/0x28) from [<c0364a34>] (ubi_io_read+0x128/0x2ec)
[    2.409910] [<c036490c>] (ubi_io_read+0x0/0x2ec) from [<c0364e30>] (ubi_io_read_ec_hdr+0x4c/0x238)
[    2.419516] [<c0364de4>] (ubi_io_read_ec_hdr+0x0/0x238) from [<c0369724>] (ubi_attach+0x148/0x149c)
[    2.429231] [<c03695dc>] (ubi_attach+0x0/0x149c) from [<c035f1e4>] (ubi_attach_mtd_dev+0x5d0/0xbc4)
[    2.438950] [<c035ec14>] (ubi_attach_mtd_dev+0x0/0xbc4) from [<c0747e2c>] (ubi_init+0x1fc/0x2c0)
[    2.448373] [<c0747c30>] (ubi_init+0x0/0x2c0) from [<c00089ec>] (do_one_initcall+0xf4/0x154)
[    2.457421] [<c00088f8>] (do_one_initcall+0x0/0x154) from [<c071eb94>] (kernel_init_freeable+0xf0/0x1bc)
[    2.467601] [<c071eaa4>] (kernel_init_freeable+0x0/0x1bc) from [<c0543408>] (kernel_init+0x10/0xec)
[    2.477318] [<c05433f8>] (kernel_init+0x0/0xec) from [<c00146f8>] (ret_from_fork+0x14/0x3c)
[    2.486224]  r4:00000000 r3:00000000
[    3.861106] UBI: scanning is finished
[    3.882019] UBI: attached mtd9 (name "NAND.file-system", size 246 MiB) to ubi0
[    3.889873] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.897147] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    3.904208] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.911568] UBI: good PEBs: 1965, bad PEBs: 3, corrupted PEBs: 0
[    3.918006] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    3.925627] UBI: max/mean erase counter: 4096/8, WL threshold: 4096, image sequence number: 145352975
[    3.935491] UBI: available PEBs: 0, total reserved PEBs: 1965, PEBs reserved for bad PEB handling: 37
[    3.945371] UBI: background thread "ubi_bgt0d" started, PID 786
[    4.001104] UBI warning: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read only 126976 bytes, retry
[    4.035107] UBI warning: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read only 126976 bytes, retry
[    4.048457] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    4.054977] davinci_mdio 4a101000.mdio: detected phy mask fffffffd
[    4.077935] libphy: 4a101000.mdio: probed
[    4.082252] davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver unknown
[    4.097038] Detected MACID = 90:9a:77:45:77:80
[    4.103115] UBI warning: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read only 126976 bytes, retry
[    4.118732] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:38:43 UTC (946687123)
[    4.156586] UBI error: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read 126976 bytes
[    4.168343] CPU: 0 PID: 786 Comm: ubi_bgt0d Not tainted 3.12.10-ti2013.12.01 #1
[    4.176141] Backtrace:
[    4.178843] [<c0017880>] (dump_backtrace+0x0/0x10c) from [<c0017a1c>] (show_stack+0x18/0x1c)
[    4.187913]  r6:cd29e000 r5:0001f000 r4:ffffffb6 r3:00000000
[    4.194050] [<c0017a04>] (show_stack+0x0/0x1c) from [<c0548750>] (dump_stack+0x20/0x28)
[    4.202641] [<c0548730>] (dump_stack+0x0/0x28) from [<c0364a34>] (ubi_io_read+0x128/0x2ec)
[    4.211504] [<c036490c>] (ubi_io_read+0x0/0x2ec) from [<c036383c>] (ubi_eba_copy_leb+0x1e8/0x544)
[    4.221016] [<c0363654>] (ubi_eba_copy_leb+0x0/0x544) from [<c0367590>] (wear_leveling_worker+0x2b0/0x6b4)
[    4.231359] [<c03672e0>] (wear_leveling_worker+0x0/0x6b4) from [<c03667ec>] (do_work+0x78/0xf4)
[    4.240683] [<c0366774>] (do_work+0x0/0xf4) from [<c036814c>] (ubi_thread+0xc8/0x178)
[    4.249059]  r6:00000000 r5:cd384000 r4:cd29e000 r3:00000000
[    4.255157] [<c0368084>] (ubi_thread+0x0/0x178) from [<c005fb74>] (kthread+0xac/0xb8)
[    4.263570] [<c005fac8>] (kthread+0x0/0xb8) from [<c00146f8>] (ret_from_fork+0x14/0x3c)
[    4.272138]  r7:00000000 r6:00000000 r5:c005fac8 r4:cd07fddc
[    4.278245] UBI warning: ubi_eba_copy_leb: error -74 while reading data from PEB 359
[    4.288987] UBIFS: background thread "ubifs_bgt0_0" started, PID 798
[    4.337787] UBIFS: recovery needed
[    4.413144] UBI warning: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read only 51200 bytes, retry
[    4.435293] UBI warning: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read only 51200 bytes, retry
[    4.457430] UBI warning: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read only 51200 bytes, retry
[    4.479559] UBI error: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read 51200 bytes
[    4.491200] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.10-ti2013.12.01 #1
[    4.498653] Backtrace:
[    4.501318] [<c0017880>] (dump_backtrace+0x0/0x10c) from [<c0017a1c>] (show_stack+0x18/0x1c)
[    4.510387]  r6:cd29e000 r5:0000c800 r4:ffffffb6 r3:00000000
[    4.516518] [<c0017a04>] (show_stack+0x0/0x1c) from [<c0548750>] (dump_stack+0x20/0x28)
[    4.525080] [<c0548730>] (dump_stack+0x0/0x28) from [<c0364a34>] (ubi_io_read+0x128/0x2ec)
[    4.533960] [<c036490c>] (ubi_io_read+0x0/0x2ec) from [<c0362298>] (ubi_eba_read_leb+0x174/0x428)
[    4.543476] [<c0362124>] (ubi_eba_read_leb+0x0/0x428) from [<c0361818>] (ubi_leb_read+0xb0/0x124)
[    4.552995] [<c0361768>] (ubi_leb_read+0x0/0x124) from [<c01fdde8>] (ubifs_leb_read+0x2c/0x90)
[    4.562208]  r8:cd358000 r7:0000012f r6:00012800 r5:0000c800 r4:cd35b240
[    4.569461] [<c01fddbc>] (ubifs_leb_read+0x0/0x90) from [<c0205b34>] (ubifs_start_scan+0x74/0xec)
[    4.578948]  r7:0000012f r6:d093b000 r5:00012800 r4:cd35b240
[    4.585049] [<c0205ac0>] (ubifs_start_scan+0x0/0xec) from [<c0217594>] (ubifs_recover_leb+0x64/0x7fc)
[    4.594908]  r8:cd35b248 r7:cd3def40 r6:00000000 r5:0000c800 r4:cd35891c
[    4.602156] [<c0217530>] (ubifs_recover_leb+0x0/0x7fc) from [<c02070b4>] (ubifs_replay_journal+0xc20/0x15f4)
[    4.612693] [<c0206494>] (ubifs_replay_journal+0x0/0x15f4) from [<c01fb860>] (ubifs_mount+0xe70/0x1674)
[    4.622766] [<c01fa9f0>] (ubifs_mount+0x0/0x1674) from [<c00d46d4>] (mount_fs+0x4c/0x18c)
[    4.631541] [<c00d4688>] (mount_fs+0x0/0x18c) from [<c00eb648>] (vfs_kern_mount+0x54/0xc8)
[    4.640409] [<c00eb5f4>] (vfs_kern_mount+0x0/0xc8) from [<c00ed4d4>] (do_mount+0x1c8/0x8c8)
[    4.649340]  r8:c07c5604 r7:cd35ba00 r6:00000000 r5:00008000 r4:c07cc49c
r3:00000000
[    4.657796] [<c00ed30c>] (do_mount+0x0/0x8c8) from [<c00edc60>] (SyS_mount+0x8c/0xc0)
[    4.666174] [<c00edbd4>] (SyS_mount+0x0/0xc0) from [<c071ef6c>] (mount_block_root+0x108/0x240)
[    4.675384]  r7:c0758f1c r6:cd354000 r5:00008000 r4:cd354000
[    4.681508] [<c071ee64>] (mount_block_root+0x0/0x240) from [<c071f354>] (prepare_namespace+0x94/0x1cc)
[    4.691484] [<c071f2c0>] (prepare_namespace+0x0/0x1cc) from [<c071ec1c>] (kernel_init_freeable+0x178/0x1bc)
[    4.701897]  r5:00000007 r4:c0770348
[    4.705771] [<c071eaa4>] (kernel_init_freeable+0x0/0x1bc) from [<c0543408>] (kernel_init+0x10/0xec)
[    4.715485] [<c05433f8>] (kernel_init+0x0/0xec) from [<c00146f8>] (ret_from_fork+0x14/0x3c)
[    4.724417]  r4:00000000 r3:00000000
[    4.728500] UBIFS error (pid 1): ubifs_recover_leb: corrupt empty space LEB 303:83968, corruption starts at 3797
[    4.739392] UBIFS error (pid 1): ubifs_scanned_corruption: corruption at LEB 303:87765
[    4.747875] UBIFS error (pid 1): ubifs_scanned_corruption: first 8192 bytes from LEB 303:87765
[    4.768020] UBIFS error (pid 1): ubifs_recover_leb: LEB 303 scanning failed
[    4.775592] UBIFS: background thread "ubifs_bgt0_0" stops
[    4.782453] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0): error -117
[    4.791202] Please append a correct "root=" boot option; here are the available partitions:
[    4.800203] 1f00             128 mtdblock0  (driver?)
[    4.805618] 1f01             128 mtdblock1  (driver?)
[    4.811059] 1f02             128 mtdblock2  (driver?)
[    4.816491] 1f03             128 mtdblock3  (driver?)
[    4.821898] 1f04             256 mtdblock4  (driver?)
[    4.827333] 1f05            1024 mtdblock5  (driver?)
[    4.832739] 1f06             128 mtdblock6  (driver?)
[    4.838174] 1f07             128 mtdblock7  (driver?)
[    4.843578] 1f08            8192 mtdblock8  (driver?)
[    4.849015] 1f09          251904 mtdblock9  (driver?)
[    4.854422] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Аватара пользователя
a.leonov

Re: Вега 2.2 не грузится

Сообщение a.leonov » Чт, 09 фев 2023 14:09

Bombandil писал(а):
Чт, 09 фев 2023 13:48
то же самое.
синяя плата и следующие данные

Код: Выделить всё

U-Boot SPL 2013.10-00189-g78d8ebd-dirty (Jul 27 2017 - 18:56:52)
CORE_AM335x_v3 module configuration
The Expected Linux image was not found. Please check your NAND configuration.
Trying to start u-boot now...
nand: bit-flip corrected @data=438
nand: bit-flip corrected @data=438


U-Boot 2013.10-00189-g78d8ebd-dirty (Jul 27 2017 - 18:56:52)

I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net:   Could not get PHY for cpsw: addr 0

Devname: cpsw

cpsw, usb_ether
Hit any key to stop autoboot:  0
Card did not respond to voltage select!
mmc0(part 0) is current device
Scanning mmc 0...
Card did not respond to voltage select!
** Bad device mmc 0 **
Card did not respond to voltage select!
mmc0(part 0) is current device
Card did not respond to voltage select!
Card did not respond to voltage select!
mmc1(part 0) is current device
Card did not respond to voltage select!
Booting from nand ...

NAND read: device 0 offset 0x80000, size 0x40000
 262144 bytes read: OK

NAND read: device 0 offset 0x200000, size 0x800000
nand: bit-flip corrected @data=448
nand: bit-flip corrected @data=182
nand: bit-flip corrected @oob=0
nand: bit-flip corrected @data=335
nand: bit-flip corrected @data=342
nand: bit-flip corrected @data=139
nand: bit-flip corrected @data=321
nand: bit-flip corrected @data=420
nand: bit-flip corrected @data=36
nand: bit-flip corrected @data=357
nand: bit-flip corrected @data=171
nand: bit-flip corrected @data=376
nand: bit-flip corrected @data=221
nand: bit-flip corrected @data=324
nand: bit-flip corrected @data=422
nand: bit-flip corrected @data=487
nand: bit-flip corrected @oob=7
nand: bit-flip corrected @data=140
nand: bit-flip corrected @data=122
nand: bit-flip corrected @data=169
 8388608 bytes read: OK
Kernel image @ 0x80200000 [ 0x000000 - 0x3d61d8 ]
## Flattened Device Tree blob at 80f80000
   Booting using the fdt blob at 0x80f80000
   Loading Device Tree to 8f320000, end 8f32bc48 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.12.10-ti2013.12.01 (root@alexander-VirtualBox) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Sat May 18 17:44:30 +07 2019
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: VEGA-BS-AM335x
[    0.000000] cma: CMA: reserved 24 MiB at 8d800000
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] AM335X ES2.1 (neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64256
[    0.000000] Kernel command line: console=ttyO0,115200n8 root=ubi0:rootfs rw ubi.mtd=NAND.file-system,2048 rootfstype=ubifs rootwait=1
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 223668K/259072K available (5415K kernel code, 553K rwdata, 1836K rodata, 329K init, 210K bss, 35404K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc071d08c   (7253 kB)
[    0.000000]       .init : 0xc071e000 - 0xc0770554   ( 330 kB)
[    0.000000]       .data : 0xc0772000 - 0xc07fc558   ( 554 kB)
[    0.000000]        .bss : 0xc07fc558 - 0xc0830e40   ( 211 kB)
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: timer1 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000345] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[    0.049698] pid_max: default: 32768 minimum: 301
[    0.049808] Security Framework initialized
[    0.049865] Mount-cache hash table entries: 512
[    0.059243] CPU: Testing write buffer coherency: ok
[    0.059659] Setting up static identity map for 0xc054ff28 - 0xc054ff98
[    0.060672] devtmpfs: initialized
[    0.062779] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    0.126492] omap_hwmod: debugss: _wait_target_disable failed
[    0.127242] pinctrl core: initialized pinctrl subsystem
[    0.128175] regulator-dummy: no parameters
[    0.130829] NET: Registered protocol family 16
[    0.133355] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.136104] cpuidle: using governor ladder
[    0.136123] cpuidle: using governor menu
[    0.146562] platform mpu.1: FIXME: clock-name 'fck' DOES NOT exist in dt!
[    0.147808] platform 49000000.edma: FIXME: clock-name 'fck' DOES NOT exist in dt!
[    0.148383] omap_gpio 44e07000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio0_pins_default, deferring probe
[    0.148412] platform 44e07000.gpio: Driver omap_gpio requests probe deferral
[    0.148756] omap_gpio 4804c000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio1_pins_default, deferring probe
[    0.148779] platform 4804c000.gpio: Driver omap_gpio requests probe deferral
[    0.149103] omap_gpio 481ac000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio2_pins_default, deferring probe
[    0.149126] platform 481ac000.gpio: Driver omap_gpio requests probe deferral
[    0.149457] omap_gpio 481ae000.gpio: could not find pctldev for node /pinmux@44e10800/mygpio3_pins_default, deferring probe
[    0.149480] platform 481ae000.gpio: Driver omap_gpio requests probe deferral
[    0.155906] omap-gpmc 50000000.gpmc: could not find pctldev for node /pinmux@44e10800/nandflash_pins_s0, deferring probe
[    0.155939] platform 50000000.gpmc: Driver omap-gpmc requests probe deferral
[    0.156376] platform 56000000.sgx: FIXME: clock-name 'fck' DOES NOT exist in dt!
[    0.158253] DSS not supported on this SoC
[    0.158269] No ATAGs?
[    0.158282] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.187109] bio: create slab <bio-0> at 0
[    0.204056] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.205013] vmmcsd_fixed: 3300 mV
[    0.209432] SCSI subsystem initialized
[    0.211063] usbcore: registered new interface driver usbfs
[    0.211277] usbcore: registered new interface driver hub
[    0.211515] usbcore: registered new device driver usb
[    0.212566] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe
[    0.212598] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral
[    0.212850] media: Linux media interface: v0.10
[    0.213057] Linux video capture interface: v2.00
[    0.213363] pps_core: LinuxPPS API ver. 1 registered
[    0.213375] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.213527] PTP clock support registered
[    0.216460] Switched to clocksource timer1
[    0.238465] NET: Registered protocol family 2
[    0.239176] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.239238] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.239275] TCP: Hash tables configured (established 2048 bind 2048)
[    0.239352] TCP: reno registered
[    0.239368] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.239391] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.239599] NET: Registered protocol family 1
[    0.240038] RPC: Registered named UNIX socket transport module.
[    0.240051] RPC: Registered udp transport module.
[    0.240060] RPC: Registered tcp transport module.
[    0.240068] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.241110] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.241793] PM: Loading am335x-pm-firmware.bin
[    0.422265] VFS: Disk quotas dquot_6.5.2
[    0.422357] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.423007] NFS: Registering the id_resolver key type
[    0.423096] Key type id_resolver registered
[    0.423107] Key type id_legacy registered
[    0.423162] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.423381] msgmni has been set to 484
[    0.425236] NET: Registered protocol family 38
[    0.425282] io scheduler noop registered
[    0.425292] io scheduler deadline registered
[    0.425316] io scheduler cfq registered (default)
[    0.427614] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.431172] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.434165] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    1.120536] console [ttyO0] enabled
[    1.125107] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    1.136398] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20
[    1.155062] brd: module loaded
[    1.164429] loop: module loaded
[    1.172496] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.181685] edma-dma-engine edma-dma-engine.0: allocated channel for 0:43
[    1.188934] edma-dma-engine edma-dma-engine.0: allocated channel for 0:42
[    1.200318] PPP generic driver version 2.4.2
[    1.205323] PPP BSD Compression module registered
[    1.210324] PPP Deflate Compression module registered
[    1.215718] PPP MPPE Compression module registered
[    1.220793] NET: Registered protocol family 24
[    1.225757] usbcore: registered new interface driver zd1201
[    1.231906] usbcore: registered new interface driver asix
[    1.237848] usbcore: registered new interface driver ax88179_178a
[    1.244489] usbcore: registered new interface driver cdc_ether
[    1.250811] usbcore: registered new interface driver r815x
[    1.256819] usbcore: registered new interface driver smsc95xx
[    1.263090] usbcore: registered new interface driver net1080
[    1.269221] usbcore: registered new interface driver cdc_subset
[    1.275671] usbcore: registered new interface driver zaurus
[    1.281799] usbcore: registered new interface driver cdc_ncm
[    1.288334] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.295213] ehci-pci: EHCI PCI platform driver
[    1.300139] ehci-omap: OMAP-EHCI Host Controller driver
[    1.306699] usbcore: registered new interface driver cdc_acm
[    1.312659] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.321316] usbcore: registered new interface driver cdc_wdm
[    1.327533] usbcore: registered new interface driver usb-storage
[    1.334318] usbcore: registered new interface driver usbserial
[    1.340686] usbcore: registered new interface driver option
[    1.346763] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.355283] mousedev: PS/2 mouse device common for all mice
[    1.362926] input: ti-tsc as /devices/ocp.2/44e0d000.tscadc/TI-am335x-tsc/input/input0
[    1.373629] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    1.381196] 44e3e000.rtc: already running
[    1.386249] i2c /dev entries driver
[    1.390590] Driver for 1-wire Dallas network protocol.
[    1.398529] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.407639] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    1.414820] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    1.457314] platform leds.3: Driver leds-gpio requests probe deferral
[    1.467501] ledtrig-cpu: registered to indicate activity on CPUs
[    1.474258] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    1.481522] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    1.489176] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    1.495280] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    1.502475] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    1.512278] usbcore: registered new interface driver usbhid
[    1.518192] usbhid: USB HID core driver
[    1.524736] oprofile: no performance counters
[    1.529850] oprofile: using timer interrupt.
[    1.534680] TCP: cubic registered
[    1.538209] Initializing XFRM netlink socket
[    1.542790] NET: Registered protocol family 17
[    1.547538] NET: Registered protocol family 15
[    1.552276] 8021q: 802.1Q VLAN Support v1.8
[    1.556727] lib80211: common routines for IEEE802.11 drivers
[    1.562796] Key type dns_resolver registered
[    1.568001] cpu cpu0: cpu0 regulator not ready, retry
[    1.573355] platform cpufreq-cpu0.0: Driver cpufreq-cpu0 requests probe deferral
[    1.581839] ThumbEE CPU extension supported.
[    1.589247] OMAP GPIO hardware version 0.1
[    1.596906] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    1.602336] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[    1.609903] ONFI param page 0 valid
[    1.613592] ONFI flash detected
[    1.616960] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (Macronix MX30LF2G18AC), 256MiB, page size: 2048, OOB size: 64
[    1.628806] omap2-nand: detected x8 NAND flash
[    1.633491] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    1.639134] omap2-nand: using custom ecc layout
[    1.644065] 10 ofpart partitions found on MTD device omap2-nand.0
[    1.650520] Creating 10 MTD partitions on "omap2-nand.0":
[    1.656230] 0x000000000000-0x000000020000 : "NAND.SPL"
[    1.663448] 0x000000020000-0x000000040000 : "NAND.SPL.backup1"
[    1.671267] 0x000000040000-0x000000060000 : "NAND.SPL.backup2"
[    1.679069] 0x000000060000-0x000000080000 : "NAND.SPL.backup3"
[    1.686879] 0x000000080000-0x0000000c0000 : "NAND.u-boot-spl-os"
[    1.694958] 0x0000000c0000-0x0000001c0000 : "NAND.u-boot"
[    1.703057] 0x0000001c0000-0x0000001e0000 : "NAND.u-boot-env"
[    1.710804] 0x0000001e0000-0x000000200000 : "NAND.u-boot-env.backup1"
[    1.719290] 0x000000200000-0x000000a00000 : "NAND.kernel"
[    1.733127] 0x000000a00000-0x000010000000 : "NAND.file-system"
[    1.948272] DCDC1: at 1500 mV
[    1.953631] vdd_core: 1100 mV
[    1.957875] vdd_mpu: 925 <--> 1350 mV at 1275 mV
[    1.963831] LDO1: at 1800 mV
[    1.967942] LDO2: at 3300 mV
[    1.972583] LDO3: 1800 mV
[    1.976415] LDO4: at 3300 mV
[    1.980331] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[    1.985975] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[    1.994900] cpufreq_cpu0: Bootloader freq 600000000Hz no match to table, Using 300000000Hz
[    2.006871] UBI: attaching mtd9 to ubi0
[    2.319010] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read only 64 bytes, retry
[    2.331490] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read only 64 bytes, retry
[    2.343956] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read only 64 bytes, retry
[    2.356415] UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 359:0, read 64 bytes
[    2.367133] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.10-ti2013.12.01 #1
[    2.374563] Backtrace:
[    2.377263] [<c0017880>] (dump_backtrace+0x0/0x10c) from [<c0017a1c>] (show_stack+0x18/0x1c)
[    2.386303]  r6:cd29e000 r5:00000040 r4:ffffffb6 r3:00000000
[    2.392456] [<c0017a04>] (show_stack+0x0/0x1c) from [<c0548750>] (dump_stack+0x20/0x28)
[    2.401047] [<c0548730>] (dump_stack+0x0/0x28) from [<c0364a34>] (ubi_io_read+0x128/0x2ec)
[    2.409910] [<c036490c>] (ubi_io_read+0x0/0x2ec) from [<c0364e30>] (ubi_io_read_ec_hdr+0x4c/0x238)
[    2.419516] [<c0364de4>] (ubi_io_read_ec_hdr+0x0/0x238) from [<c0369724>] (ubi_attach+0x148/0x149c)
[    2.429231] [<c03695dc>] (ubi_attach+0x0/0x149c) from [<c035f1e4>] (ubi_attach_mtd_dev+0x5d0/0xbc4)
[    2.438950] [<c035ec14>] (ubi_attach_mtd_dev+0x0/0xbc4) from [<c0747e2c>] (ubi_init+0x1fc/0x2c0)
[    2.448373] [<c0747c30>] (ubi_init+0x0/0x2c0) from [<c00089ec>] (do_one_initcall+0xf4/0x154)
[    2.457421] [<c00088f8>] (do_one_initcall+0x0/0x154) from [<c071eb94>] (kernel_init_freeable+0xf0/0x1bc)
[    2.467601] [<c071eaa4>] (kernel_init_freeable+0x0/0x1bc) from [<c0543408>] (kernel_init+0x10/0xec)
[    2.477318] [<c05433f8>] (kernel_init+0x0/0xec) from [<c00146f8>] (ret_from_fork+0x14/0x3c)
[    2.486224]  r4:00000000 r3:00000000
[    3.861106] UBI: scanning is finished
[    3.882019] UBI: attached mtd9 (name "NAND.file-system", size 246 MiB) to ubi0
[    3.889873] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.897147] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    3.904208] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.911568] UBI: good PEBs: 1965, bad PEBs: 3, corrupted PEBs: 0
[    3.918006] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    3.925627] UBI: max/mean erase counter: 4096/8, WL threshold: 4096, image sequence number: 145352975
[    3.935491] UBI: available PEBs: 0, total reserved PEBs: 1965, PEBs reserved for bad PEB handling: 37
[    3.945371] UBI: background thread "ubi_bgt0d" started, PID 786
[    4.001104] UBI warning: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read only 126976 bytes, retry
[    4.035107] UBI warning: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read only 126976 bytes, retry
[    4.048457] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    4.054977] davinci_mdio 4a101000.mdio: detected phy mask fffffffd
[    4.077935] libphy: 4a101000.mdio: probed
[    4.082252] davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver unknown
[    4.097038] Detected MACID = 90:9a:77:45:77:80
[    4.103115] UBI warning: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read only 126976 bytes, retry
[    4.118732] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:38:43 UTC (946687123)
[    4.156586] UBI error: ubi_io_read: error -74 (ECC error) while reading 126976 bytes from PEB 359:4096, read 126976 bytes
[    4.168343] CPU: 0 PID: 786 Comm: ubi_bgt0d Not tainted 3.12.10-ti2013.12.01 #1
[    4.176141] Backtrace:
[    4.178843] [<c0017880>] (dump_backtrace+0x0/0x10c) from [<c0017a1c>] (show_stack+0x18/0x1c)
[    4.187913]  r6:cd29e000 r5:0001f000 r4:ffffffb6 r3:00000000
[    4.194050] [<c0017a04>] (show_stack+0x0/0x1c) from [<c0548750>] (dump_stack+0x20/0x28)
[    4.202641] [<c0548730>] (dump_stack+0x0/0x28) from [<c0364a34>] (ubi_io_read+0x128/0x2ec)
[    4.211504] [<c036490c>] (ubi_io_read+0x0/0x2ec) from [<c036383c>] (ubi_eba_copy_leb+0x1e8/0x544)
[    4.221016] [<c0363654>] (ubi_eba_copy_leb+0x0/0x544) from [<c0367590>] (wear_leveling_worker+0x2b0/0x6b4)
[    4.231359] [<c03672e0>] (wear_leveling_worker+0x0/0x6b4) from [<c03667ec>] (do_work+0x78/0xf4)
[    4.240683] [<c0366774>] (do_work+0x0/0xf4) from [<c036814c>] (ubi_thread+0xc8/0x178)
[    4.249059]  r6:00000000 r5:cd384000 r4:cd29e000 r3:00000000
[    4.255157] [<c0368084>] (ubi_thread+0x0/0x178) from [<c005fb74>] (kthread+0xac/0xb8)
[    4.263570] [<c005fac8>] (kthread+0x0/0xb8) from [<c00146f8>] (ret_from_fork+0x14/0x3c)
[    4.272138]  r7:00000000 r6:00000000 r5:c005fac8 r4:cd07fddc
[    4.278245] UBI warning: ubi_eba_copy_leb: error -74 while reading data from PEB 359
[    4.288987] UBIFS: background thread "ubifs_bgt0_0" started, PID 798
[    4.337787] UBIFS: recovery needed
[    4.413144] UBI warning: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read only 51200 bytes, retry
[    4.435293] UBI warning: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read only 51200 bytes, retry
[    4.457430] UBI warning: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read only 51200 bytes, retry
[    4.479559] UBI error: ubi_io_read: error -74 (ECC error) while reading 51200 bytes from PEB 359:79872, read 51200 bytes
[    4.491200] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.10-ti2013.12.01 #1
[    4.498653] Backtrace:
[    4.501318] [<c0017880>] (dump_backtrace+0x0/0x10c) from [<c0017a1c>] (show_stack+0x18/0x1c)
[    4.510387]  r6:cd29e000 r5:0000c800 r4:ffffffb6 r3:00000000
[    4.516518] [<c0017a04>] (show_stack+0x0/0x1c) from [<c0548750>] (dump_stack+0x20/0x28)
[    4.525080] [<c0548730>] (dump_stack+0x0/0x28) from [<c0364a34>] (ubi_io_read+0x128/0x2ec)
[    4.533960] [<c036490c>] (ubi_io_read+0x0/0x2ec) from [<c0362298>] (ubi_eba_read_leb+0x174/0x428)
[    4.543476] [<c0362124>] (ubi_eba_read_leb+0x0/0x428) from [<c0361818>] (ubi_leb_read+0xb0/0x124)
[    4.552995] [<c0361768>] (ubi_leb_read+0x0/0x124) from [<c01fdde8>] (ubifs_leb_read+0x2c/0x90)
[    4.562208]  r8:cd358000 r7:0000012f r6:00012800 r5:0000c800 r4:cd35b240
[    4.569461] [<c01fddbc>] (ubifs_leb_read+0x0/0x90) from [<c0205b34>] (ubifs_start_scan+0x74/0xec)
[    4.578948]  r7:0000012f r6:d093b000 r5:00012800 r4:cd35b240
[    4.585049] [<c0205ac0>] (ubifs_start_scan+0x0/0xec) from [<c0217594>] (ubifs_recover_leb+0x64/0x7fc)
[    4.594908]  r8:cd35b248 r7:cd3def40 r6:00000000 r5:0000c800 r4:cd35891c
[    4.602156] [<c0217530>] (ubifs_recover_leb+0x0/0x7fc) from [<c02070b4>] (ubifs_replay_journal+0xc20/0x15f4)
[    4.612693] [<c0206494>] (ubifs_replay_journal+0x0/0x15f4) from [<c01fb860>] (ubifs_mount+0xe70/0x1674)
[    4.622766] [<c01fa9f0>] (ubifs_mount+0x0/0x1674) from [<c00d46d4>] (mount_fs+0x4c/0x18c)
[    4.631541] [<c00d4688>] (mount_fs+0x0/0x18c) from [<c00eb648>] (vfs_kern_mount+0x54/0xc8)
[    4.640409] [<c00eb5f4>] (vfs_kern_mount+0x0/0xc8) from [<c00ed4d4>] (do_mount+0x1c8/0x8c8)
[    4.649340]  r8:c07c5604 r7:cd35ba00 r6:00000000 r5:00008000 r4:c07cc49c
r3:00000000
[    4.657796] [<c00ed30c>] (do_mount+0x0/0x8c8) from [<c00edc60>] (SyS_mount+0x8c/0xc0)
[    4.666174] [<c00edbd4>] (SyS_mount+0x0/0xc0) from [<c071ef6c>] (mount_block_root+0x108/0x240)
[    4.675384]  r7:c0758f1c r6:cd354000 r5:00008000 r4:cd354000
[    4.681508] [<c071ee64>] (mount_block_root+0x0/0x240) from [<c071f354>] (prepare_namespace+0x94/0x1cc)
[    4.691484] [<c071f2c0>] (prepare_namespace+0x0/0x1cc) from [<c071ec1c>] (kernel_init_freeable+0x178/0x1bc)
[    4.701897]  r5:00000007 r4:c0770348
[    4.705771] [<c071eaa4>] (kernel_init_freeable+0x0/0x1bc) from [<c0543408>] (kernel_init+0x10/0xec)
[    4.715485] [<c05433f8>] (kernel_init+0x0/0xec) from [<c00146f8>] (ret_from_fork+0x14/0x3c)
[    4.724417]  r4:00000000 r3:00000000
[    4.728500] UBIFS error (pid 1): ubifs_recover_leb: corrupt empty space LEB 303:83968, corruption starts at 3797
[    4.739392] UBIFS error (pid 1): ubifs_scanned_corruption: corruption at LEB 303:87765
[    4.747875] UBIFS error (pid 1): ubifs_scanned_corruption: first 8192 bytes from LEB 303:87765
[    4.768020] UBIFS error (pid 1): ubifs_recover_leb: LEB 303 scanning failed
[    4.775592] UBIFS: background thread "ubifs_bgt0_0" stops
[    4.782453] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0): error -117
[    4.791202] Please append a correct "root=" boot option; here are the available partitions:
[    4.800203] 1f00             128 mtdblock0  (driver?)
[    4.805618] 1f01             128 mtdblock1  (driver?)
[    4.811059] 1f02             128 mtdblock2  (driver?)
[    4.816491] 1f03             128 mtdblock3  (driver?)
[    4.821898] 1f04             256 mtdblock4  (driver?)
[    4.827333] 1f05            1024 mtdblock5  (driver?)
[    4.832739] 1f06             128 mtdblock6  (driver?)
[    4.838174] 1f07             128 mtdblock7  (driver?)
[    4.843578] 1f08            8192 mtdblock8  (driver?)
[    4.849015] 1f09          251904 mtdblock9  (driver?)
[    4.854422] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Добрый день!

Критическая ошибка.
Вам необходимо отправить БС в ремонт. Для получения информации, Вам нужно обратиться по e-mail: remont@vega-absolute.ru

Ответить